Teroson UP 150 Glass Fibre Filler - 750g
Teroson UP 150 is a two-part unsaturated polyester body filler used for bridging and repairing holes on many surfaces such as steel, aluminium, galvanized surfaces and glass fibre. The right solution for lots of marine filling applications and not only!.
Formerly known as Plastic Padding Glass Fibre Filler now is sold under the Teroson fillers brand owned by the Henkel company.
The product consists of 2 parts - 1 part 15g x UP 190 hardener and 1 part x 743g of Teroson UP 150 filler.
Teroson UP 150 Technical Data
Component A
- Colour - Blue
- Odour - Styrene
- Density - Approx. 1.82 g/cm³
Component B
- Colour - Red
- Odour - Neutral
- Density - Approx. 1.1 g/cm³
Mix ratio (Component A + B combined)
- Mixing ratio by volume - 100:2-3
- Pot life (20 °C, 50% rh) - 6.5 min.
- Grinding - Allow 20 to 30min to cure
Surface preparation prior to application of Teroson UP 150
Prior to using the Teroson glass fibre filler please ensure that the application surface dust-free, clean, dry and free from grease or other loose particles. If applied on metal we recommend removing the rust and sand down the area to bare metal for better adhesion.
For areas covered with paint please make sure that the paint has a good adhesion to the surface so that you can apply the UP 150 filler straight onto the painted surface. If not sure, remove the paint before application for best results.
Teroson UP 150 application instructions
- In order to achieve a perfect mix of fibre glass filler, mix the mass in a ratio of a golf ball size (40ml) with 4 to 5cm (2 to 3%) long hardener stripe of Teroson UP 150 using a mixing stick or the supplied spreader until a uniform colour has been achieved.
- Soon as the mixing is ready, apply the glass fibre filler within 6.5 minutes if the temperature is around 20°C. If the temperature inside the room or outside is higher than 20°C we recommend applying it as soon as possible before it starts to go off.
- Apply a sufficient amount of filler onto the dent, scratch or hole so that you have a thin layer of UP 150 above the surface and allows you to sand paper it with a 150 grit in order to achieve a smoother finish in the end.
- For thicker layers should be built up using multiple layers. Allow up to
30 minutes to dry before sanding.
Original: $34.65
-65%$34.65
$12.13Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Teroson UP 150 is a two-part unsaturated polyester body filler used for bridging and repairing holes on many surfaces such as steel, aluminium, galvanized surfaces and glass fibre. The right solution for lots of marine filling applications and not only!.
Formerly known as Plastic Padding Glass Fibre Filler now is sold under the Teroson fillers brand owned by the Henkel company.
The product consists of 2 parts - 1 part 15g x UP 190 hardener and 1 part x 743g of Teroson UP 150 filler.
Teroson UP 150 Technical Data
Component A
- Colour - Blue
- Odour - Styrene
- Density - Approx. 1.82 g/cm³
Component B
- Colour - Red
- Odour - Neutral
- Density - Approx. 1.1 g/cm³
Mix ratio (Component A + B combined)
- Mixing ratio by volume - 100:2-3
- Pot life (20 °C, 50% rh) - 6.5 min.
- Grinding - Allow 20 to 30min to cure
Surface preparation prior to application of Teroson UP 150
Prior to using the Teroson glass fibre filler please ensure that the application surface dust-free, clean, dry and free from grease or other loose particles. If applied on metal we recommend removing the rust and sand down the area to bare metal for better adhesion.
For areas covered with paint please make sure that the paint has a good adhesion to the surface so that you can apply the UP 150 filler straight onto the painted surface. If not sure, remove the paint before application for best results.
Teroson UP 150 application instructions
- In order to achieve a perfect mix of fibre glass filler, mix the mass in a ratio of a golf ball size (40ml) with 4 to 5cm (2 to 3%) long hardener stripe of Teroson UP 150 using a mixing stick or the supplied spreader until a uniform colour has been achieved.
- Soon as the mixing is ready, apply the glass fibre filler within 6.5 minutes if the temperature is around 20°C. If the temperature inside the room or outside is higher than 20°C we recommend applying it as soon as possible before it starts to go off.
- Apply a sufficient amount of filler onto the dent, scratch or hole so that you have a thin layer of UP 150 above the surface and allows you to sand paper it with a 150 grit in order to achieve a smoother finish in the end.
- For thicker layers should be built up using multiple layers. Allow up to
30 minutes to dry before sanding.
